Gallons
Calculating Gallons in a Cylinder
Turn tank or container dimensions into gallons in one tap — with a clear US vs Imperial gallon choice so you never mix the two up.
The single most important thing a calculating gallons in a cylinder has to get right is which gallon you mean. A US gallon and an Imperial gallon are not the same size, so this tool asks you to choose — and shows both, so there is never any doubt about the number you are reading.
Capacity questions almost always end in gallons — filling a stock trough, ordering heating oil, dosing a pool. The catch is that a gallon is not one fixed thing, so the same tank can be 200 gallons or 240 gallons depending on which side of the Atlantic you are standing on.
Using the calculator
- Measure across the circular end — the diameter or radius.
- If you measured the diameter, halve it to get the radius r.
- Square the radius and multiply by π to get the base area.
- Multiply the base area by the height h: V = π r² h.
- Convert the result into your preferred unit above.
Getting an accurate measurement
Measure the inside diameter of a tank, not the outside — the wall does not hold liquid. Keep every measurement in the same system, and let the tool convert between units for you.
The maths in one line
The volume of a cylinder is:
V = π r² hA worked example
Worked example. Take a cylinder with a diameter of 30 in (so a radius of 15 in) and a height of 48 in. The base area is π × 15² = 706.86 in², and multiplying by the height gives a volume of about 146.9 US gallons (33,929 in³ · 556.0 litres).
| Unit | Equal to |
|---|---|
| 1 US gallon | 231 in³ · 3.785 L |
| 1 Imperial gallon | 277.42 in³ · 4.546 L |
| 1 cubic foot | 7.481 US gal · 28.32 L |
| 1 litre | 0.264 US gal · 0.220 Imp gal |
| 1 US gallon | 128 US fl oz |
These are geometric gallons from the dimensions you enter. A real tank holds slightly less once wall thickness, fittings and headspace are taken into account — and always confirm whether you need US or Imperial gallons.
Conversions use standard factors: 1 US gallon = 231 in³, 1 Imperial gallon = 4.54609 L, 1 litre = 1000 cm³.
After you have your answer
To save you a second search, here are the related answers people most often want straight after this calculation:
How many litres is that in metric?
Every gallons result on this page is shown next to its litre value in the breakdown, because 1 US gallon is about 3.785 litres and 1 Imperial gallon is about 4.546 litres. You can hand the same figure to anyone regardless of which system they use.
What if I only measured around the outside?
You do not need the diameter directly. Measure the circumference around the tank, switch the base input to circumference, and the tool divides by 2 pi to find the radius before working out the gallons.
How much does a full tank weigh?
Water is about 8.34 lb per US gallon, or 1 kg per litre. Tick estimate weight, choose water, and the calculator multiplies the volume by density to show the load a full tank puts on its stand or floor.
How do I read a tank that is only part full?
For an upright tank, enter the current liquid height instead of the full height. For a tank lying on its side, use the horizontal-tank mode, which turns a dip depth into gallons using the correct segment maths.
Where people use this
A few of the jobs it gets used for:
- Sizing a water storage or rainwater tank
- Working out fuel or oil drum capacity
- Estimating how many gallons a pool or trough holds
- Checking a well or cistern volume
Where people go wrong
The mistakes that cost the most are unit mistakes. Reading a US figure as Imperial, or the reverse, is a 20% error before you start. Measuring the outside of a tank instead of the inside quietly overstates capacity, and forgetting the headspace at the top overstates it again. Measure inside, confirm which gallon, and treat the result as a full-to-the-brim maximum.
One result, every unit
Because volume units are where most errors creep in, the tool does the converting for you. Enter your measurements once and every common unit appears together, from millilitres up to cubic metres and across to US and Imperial gallons. Pick whichever the task calls for and lift the rest from the list; nothing needs a second calculation. The result also updates live as you change a measurement, so you can compare two sizes quickly without starting over.
Related things you might need
Once you have your answer you may also want to work in tank capacity litres & liters cubic feet. These related calculators pick up where this one leaves off:
The bottom line: with the radius or diameter and the height, the volume follows immediately, and the breakdown lets you hand the same number to anyone in the unit they prefer. Measure inside dimensions for anything that holds liquid, leave a little headspace at the top of a real container, and treat the geometric figure as a clean maximum rather than the final word on usable capacity.
Questions people ask
What is the formula for the volume of a cylinder?
V = π r² h — the area of the circular base (π r²) multiplied by the height (h). If you have the diameter instead of the radius, halve it first: r = d ÷ 2.