Half cylinder
Formula for Volume of a Half Cylinder
Exactly half of a full cylinder — a semicircular trough or channel. Enter radius and length for the volume.
Troughs, channels and half-round tanks all use the half-cylinder shape, and this formula for volume of a half cylinder sizes them instantly: enter the radius or diameter and the length, and read half the full-cylinder volume.
Half cylinders show up as troughs, channels, gutters and half-round tanks. The shape is forgiving because it is simply half of something familiar, so the maths never gets harder than work out the full cylinder, then halve it.
Using the calculator
- Measure the radius (or diameter) of the semicircular end.
- Measure the length of the half cylinder.
- Work out the full-cylinder volume π r² h.
- Halve it — a half cylinder is exactly 50% of the full shape.
Getting an accurate measurement
If you can only reach the top, measure the diameter across the opening and halve it. Keep every measurement in the same system, and let the tool convert between units for you.
The maths in one line
The volume of a half cylinder is:
V = ½ π r² hA worked example
Worked example. Take a cylinder with a diameter of 10 cm (so a radius of 5 cm) and a height of 25 cm. The base area is π × 5² = 78.54 cm², and multiplying by the height gives a volume of about 1.96 litres (1,963 cm³ · 0.52 US gallons).
For anything that holds liquid, measure the inside of the cylinder — the wall takes up space that the contents cannot.
Conversions use standard factors: 1 US gallon = 231 in³, 1 Imperial gallon = 4.54609 L, 1 litre = 1000 cm³.
Once the result is in
The figure above is usually the start, not the finish. These are the questions that tend to come next, answered here so you do not have to run another search:
What is the flat cross-section area?
The semicircular end has area one half pi r squared. Multiplying by the length gives the volume, which is what the tool reports.
Could I use this for a trough or gutter?
Yes. A half-round trough or channel is a half cylinder, so its capacity is one half pi r squared times the length, in whatever unit you choose.
How do I get its weight or capacity in litres?
Read the volume in litres from the breakdown for capacity, or tick estimate weight and add a density to get the mass of a solid half-round piece.
How does this relate to the full cylinder?
A half cylinder is exactly 50% of the full shape with the same radius and length, so if you know the full volume you can simply halve it.
Common uses
It comes in handy across quite different tasks:
- Sizing a half-round trough or gutter
- Volume of a semicircular channel
- A half-cylinder feature or planter
Where people go wrong
Two things trip people up: squaring the wrong number, and forgetting that the answer is cubic. If a result looks four times too big or too small, you have probably swapped radius and diameter somewhere, so it is always worth re-reading the measurement you are least sure of. It also helps to glance at the equivalent units; if the litre and gallon figures are both off by the same factor, the input is the culprit, not the maths.
Reading and converting your result
Showing every unit at once is about speed and safety: you see the answer in litres, gallons and cubic feet side by side, so there is no chance of applying the wrong conversion factor. Change the output unit at the top to make any of them the headline figure, switch the precision to exact if you want the value in terms of pi, and use copy-result to paste a tidy summary wherever you need it.
What to work out next
Once you have your answer you may also want to work in cylinder volume volume formula tank capacity. These related calculators pick up where this one leaves off:
The bottom line: with the radius or diameter and the height, the volume follows immediately, and the breakdown lets you hand the same number to anyone in the unit they prefer. Measure inside dimensions for anything that holds liquid, leave a little headspace at the top of a real container, and treat the geometric figure as a clean maximum rather than the final word on usable capacity.
Questions people ask
What is the formula for the volume of a cylinder?
V = π r² h — the area of the circular base (π r²) multiplied by the height (h). If you have the diameter instead of the radius, halve it first: r = d ÷ 2.Do I use radius or diameter?
What units can I use?
Is the volume of a cylinder squared or cubed?
Does this work for a tank or a pipe?
What is the formula for a half cylinder?
V = ½ π r² h — exactly half the volume of the full cylinder with the same radius and length.