Gallons
Gallons of a Cylinder
Turn tank or container dimensions into gallons in one tap — with a clear US vs Imperial gallon choice so you never mix the two up.
The single most important thing a gallons of a cylinder has to get right is which gallon you mean. A US gallon and an Imperial gallon are not the same size, so this tool asks you to choose — and shows both, so there is never any doubt about the number you are reading.
Capacity questions almost always end in gallons — filling a stock trough, ordering heating oil, dosing a pool. The catch is that a gallon is not one fixed thing, so the same tank can be 200 gallons or 240 gallons depending on which side of the Atlantic you are standing on.
How the calculation works
- Measure across the circular end — the diameter or radius.
- If you measured the diameter, halve it to get the radius r.
- Square the radius and multiply by π to get the base area.
- Multiply the base area by the height h: V = π r² h.
- Convert the result into your preferred unit above.
Getting an accurate measurement
Measure the inside diameter of a tank, not the outside — the wall does not hold liquid. Keep every measurement in the same system, and let the tool convert between units for you.
How the volume is worked out
The volume of a cylinder is:
V = π r² hA worked example
Worked example. Take a cylinder with a diameter of 30 in (so a radius of 15 in) and a height of 48 in. The base area is π × 15² = 706.86 in², and multiplying by the height gives a volume of about 146.9 US gallons (33,929 in³ · 556.0 litres).
| Unit | Equal to |
|---|---|
| 1 US gallon | 231 in³ · 3.785 L |
| 1 Imperial gallon | 277.42 in³ · 4.546 L |
| 1 cubic foot | 7.481 US gal · 28.32 L |
| 1 litre | 0.264 US gal · 0.220 Imp gal |
| 1 US gallon | 128 US fl oz |
These are geometric gallons from the dimensions you enter. A real tank holds slightly less once wall thickness, fittings and headspace are taken into account — and always confirm whether you need US or Imperial gallons.
Conversions use standard factors: 1 US gallon = 231 in³, 1 Imperial gallon = 4.54609 L, 1 litre = 1000 cm³.
Follow-on questions, answered
The figure above is usually the start, not the finish. These are the questions that tend to come next, answered here so you do not have to run another search:
How do I read a tank that is only part full?
For an upright tank, enter the current liquid height instead of the full height. For a tank lying on its side, use the horizontal-tank mode, which turns a dip depth into gallons using the correct segment maths.
Is the answer US or Imperial?
Both are shown at once. In the United States use US gallons; most other English-speaking countries use the larger Imperial gallon. Mixing the two is the single most common tank-sizing error.
How many litres is that in metric?
Every gallons result on this page is shown next to its litre value in the breakdown, because 1 US gallon is about 3.785 litres and 1 Imperial gallon is about 4.546 litres. You can hand the same figure to anyone regardless of which system they use.
What if I only measured around the outside?
You do not need the diameter directly. Measure the circumference around the tank, switch the base input to circumference, and the tool divides by 2 pi to find the radius before working out the gallons.
Common uses
A few of the jobs it gets used for:
- Sizing a water storage or rainwater tank
- Working out fuel or oil drum capacity
- Estimating how many gallons a pool or trough holds
- Checking a well or cistern volume
Common mistakes to avoid
The mistakes that cost the most are unit mistakes. Reading a US figure as Imperial, or the reverse, is a 20% error before you start. Measuring the outside of a tank instead of the inside quietly overstates capacity, and forgetting the headspace at the top overstates it again. Measure inside, confirm which gallon, and treat the result as a full-to-the-brim maximum.
One result, every unit
Because volume units are where most errors creep in, the tool does the converting for you. Enter your measurements once and every common unit appears together, from millilitres up to cubic metres and across to US and Imperial gallons. Pick whichever the task calls for and lift the rest from the list; nothing needs a second calculation. The result also updates live as you change a measurement, so you can compare two sizes quickly without starting over.
Related things you might need
Once you have your answer you may also want to work in tank capacity litres & liters cubic feet. These related calculators pick up where this one leaves off:
To sum up, the whole job is two measurements and one formula. Enter them above, pick your unit, and you have an accurate figure plus every equivalent unit beside it. Keep a copy with the copy-result button, save the shareable link if someone else needs the same numbers, and use the history panel to compare a few options without starting from scratch.